CTAC-TECH company,

5 Esplanade Compans Caffarelli Building A - CS 57130 - 31071 TOULOUSE CEDEX 7

Version: Flipr HUBcontact@flipr.fr

Maximum characterization

Flipr HUB works with mono and three-phase to be compatible with a large majority of pump. However, the device shall not exceed the following maximum characteristics:

Food

1 phase 220/240V AC 50/60Hz

Cons. 5W (1W) CHARGE

1 phase 220/240V AC - 3.0KW - 3.0 Hp

3 phase 315/400V AC - 5.5KW - 6 Hp

50/60Hz

A mandatory maximum 16A circuit breaker must be upstream of the device.

Any intervention and assembly of the device by an unqualified person shall give an end to the manufacturer's legal guarantees and hidden screws.

Operating temperature -5° to 45° Wireless standard: 802.11 b/g/n

Security Mechanism: WPA/WPA2 Bluetooth: Classic / BLE

Attention! Do not use in a damp place. Disconnect the current before installation of the module

By this CTAC-TECH states that the appliance complies with the essential requirements and other relevant provisions of the Directive: EN 62311, EN 300 328, RED 2014/53/EU, EN 301489-17, EN 60669-1:1999/A1/, EN 60669-2-

1,2004/A1/a12, en 50428: 2005 / a1: 2007 / a2: 2009

Flipr Hub is an intelligent automated pool system and should not be used for any other use. During the installation, you will take action on the electric network of your pool.

It is advisable to have expertise in the field of electricity or to use a qualified technician who has previously received instructions for use (by reading this notice) in accordance with current local standards.

The installer is responsible for the installation of the device and compliance with local installation regulations. In no event shall the manufacturer be liable for non-compliance with standards or installation instructions, or damage resulting from an installation or use error.

If there is any doubt about your installation, contact a qualified technician to verify your technical room.

In case of malfunction of the device, do not attempt to repair the device by yourself. Do not change the device. Any changes can be dangerous for users. The manufacturer has all liability for the use of parts or materials that are not compliant and/or incompatible with Flipr HUB. Only a qualified person can intervene on the device in the event of a failure or to maintain it.

Any handling by unqualified and/or unauthorized personnel automatically results in the removal of the warranty. Similarly, replacing parts with parts other than parts of manufacturer origin may pose a hazard, and end the device warranty.

Failure to comply with the previous instructions may result in serious material or body shortages that may result in death.

Ensure a good wifi connection. Test the network before installation.

Keep out of reach of children.

Before any technical intervention on the device, imperatively cut off the electrical power supply of the device and any other equipment connected to it.

Do not install the appliance in a place at risk of contact with water, wet, unvened or exposed to corrosive external agents.

Do not reassemble the device. Never intervene on the device with wet hands and/or feet or bare feet.

Always put back and rework the cable protections before using the product.

Cover with rubber cable protector and screws (2x)

Flipr Hub device

Wall fixing kit (2x screws & dowels)

Front view

Light

Button function / stop

Towers

Electric block

Location of the HUB

Selected equipment

The electric block must be higher than the Flipr HUB, and the equipment chosen below. Be careful: use as a reference the logo that must be read in the direction of reading. Refer to the connector references on the housing

Drill your support (wall or other) using the drilling guide. Place ankle at each hole (included). Attach the HUB using the supplied screws.

10

Download the Flipr app, it will guide you through the next steps!

Cut the circuit breaker of the mandatory device at the electric block. Then check that the pump is well disconnected.

Be careful, your circuit breaker must be upstream of the device to respect the mounting.

Switch to the stage only if the power is turned off and the hub is securely attached to the wall!

Cut the cable at the chosen location and refrain it. Leave about 5cm of colored sheath

1and 1cm of copper.

2

3

Cut the Rubber eyelet according to the size of the cable Thread the cable into the Rubber eyelet.

Attention to the meaning (see

schema).

There are several cable colors and 6 connection possibilities followed your installation. Go to the next page for color possibilities.

It is very important to connect them to the requested location on the schema!

All blue colour blue and yellow / green

New

Gris

Bleu

Yellow / green

Colour code of cables

Monophase with 2 cables

Monophase with 3 cables

Single-phase with low current (<90V)

A

B

C

D

E

A

B

C

D

E

1

2

3

4

5

1

2

3

5

Single-phase - equipped with devices for simultaneous operation

Three-phase with 5 cables

No neutral (think to pull a cable)

1

2

Clip the cables using the orange iron-moirs. Respect the correct order, if you are not sure to take the previous patterns.

After plugging and clipping the cables, check the connection by pulling slightly at each of the cables. If these cables do not detach from the connector then you can place the "connector cover" and then place the screw to seal the housing on both sides.

Once the connections are finalized, you can establish the electric current. Flipr Hub will automatically start, and light will appear on the device. Connect Flipr HUB to the WIFI network via the Flipr app.

If at the start of Flipr Hub, one of the events following this productCut immediatment the court of the electrical tableau. Verify

all connections. If you do not find

where the problem comes, contact our support or a professional close to you.

• If the circuit breaker jumps

• If you feel or see smoke

• If there are no LEDs on the HUB at this level (blue dot)

Manual mode

Inactive Active Active

Programmator or smart control

ActiveInactive

ANOMALIES (alternating flashing

with the color of the fashion)

Orange - The hub is not connected to the network

Red - The hub is connected to the wifi network but does not receive data.

1

3

2

4

In the app, you should see the Hub appear. Enter the security key (labelled label “IDâ€TM inside one of the two hoods)

You sailequipped with a Hub! you can at any timeaccess and controlyour Flipr Hub via the Hub button at the top right ofDashboard screen.

Button “HUBâ€

27

You canparameteryour Hub (rename, change WIFI network, ...) via thebutton settings(notched wheel)

You canAddanother Hub orswitchbetween several Hub via theon the rightthe name of your equipment.

In themenu Hubfrom the Flipr app you will find3 main features, the modeManual, the modeProgrammeand the modeSmartControl

Manual

Program mode

SmartControl mode

Themanual modeis activated by default. A â€'s switch†allows youto turn onorto turn offyour equipment permanently. In this mode the light of the Hub will beBlanchif in arrest andVeryif in motion.

Themode programallows you to regulateoperating rangesvia a virtual mechanical clock. In this mode the light of the Hub will beVioletin arrest andBleuon the move.

Foradd a programclick on the “+â€" at the top right of the screen. Then choose themoperating niche(1 notch = 1h) andthe dayson which the nursery must reproduce. Think about givinga nameto your program!

The modeSmartControlautomates equipment. for exampleautomatically controlleddepending on the temperature of the water.* * * * * *

*requires a START with infinite subscription or START MAX